|
|
|
Baby Nursery Furniture - A Booming Market!
Baby Nursery Furniture - A Booming Market!
Baby nursery furniture and baby crib sets are a growing category, representing $1.1 billion at retail last year, and expected to grow to $1.4 billion by 2009. Today's baby furniture varies quite a bit...
Buying Gently Used Baby Clothing
Remember that adorable outfit you bought for your newborn - the one that cost you nearly $40, and got worn three times before it no longer fit? For such tiny things, baby clothing is expensive - and as fast as babies grow, they seldom see much wear....
Fighting that Feeling of Failure
As mothers, we are often our own worst enemies. We set amazingly high standards for ourselves, forgetting that motherhood is the toughest job in the world.
There are definitely limits to our patience and long-suffering. We are not robots without...
Help I am Pregnant and an Addict
There are a lot of resources on the internet, in books, and from the medical community on the dangers of drug and alcohol use during pregnancy. However, there is not very much quality information on what you should do if you have a problem with...
Honey I can’t afford the kids
Sex has a lot to answer for … babies usually … which then with time and much financial investment grow up to be beautiful mutations of their parents. Yet as the family absorbs more money as it grows, the need for financial planning and protection...
|
|
| |
|
|
|
|
|
from our sponsors
Internet Home Business Training Course
|
Creating A Baby Belly Mold Part 2 of 2
Welcome Back to Creating a Baby
Belly Mold
Step Four:
Now comes the fun part. You want to have a couple of bowls of water handy. Change
the water if it starts to get "creamy".
Instructions for the plaster depends on the kind you buy but they are all are
pretty close.
Fill the bowls up with water, tempeture should be around 22-25 degres celcis.
Take the bandges and immerse them into the water for 3-5 seconds. When you take
the bandgage out hold the 2 ends up in the air close to each other and let the
extra water drip off.
Now start applying the banges from top down or the bottome up (it doesnt matter).
When appling the bandages apply them in a angle. Dont apply then straight across
the belly. If you apply them straight across it will not be as stong as if you
did it on an angle.
Keep doing this all the way up or down.
When we finished we went back over the entire mold again , just to give it a
little extra strenght. Try to do the second before the first hardens.
Step Five:
Now you have to wait until the mold dries. As the mold dries it will give off
heat, this is normal.
How long it takes to drie depends on how many coats your put on , how wet the
cast was and
Didn't Find What You Were Looking For?
Try a Specialized Search HERE
what temp the water was. It took about 15 minutes before we could
take our mold off.
The easiest way to tell is reach down the side of the mold and try to pull it
off a bit, if it is really flemzy then leave it until it is somewhat firm.
While you are waiting the person helping can start to clean up the mess you
made. The plaster will come off with soap and water, its easier to get off when
its still soft.
When you think its time to remove the mold , pull up on the seran wrap , not
the mold . The seran wrap will come off very easily.
Put the cast at room temp somewere out of the way and let dry until its harded.
Step Six:
Now its time to finish your mold.
You don't have to sand it but if you want it smooth then take 80 grit sand paper
to the mold. Sand it until its smooth.
Now you can paint your mold, let your imagination go wild here. Remember little
babies love bright colors.
The only thing i can suggest is use a water base paint, some paints will eat
the plaster .
That's it your done.
I hope this will preserve your beautiful belly for a life time to come..
About the Author
Author is the writer for many sites including Las
Vegas Help. and Baby Shower Help
|
|
|
|
|
|
